SD-Kartenschacht nicht erkannt

[krellaan]

Moin.

Mit dem Kernel 3.6-x.towo-siduction-686 erkennt der Rechner nicht mehr, dass ich eine SD-Karte in den Schacht stecke. Mit den Kernel 3.5-x.towo-siduction-686 funktioniert die automatische Erkennung noch.

[dibl]

I just checked with an SDHC card in these two siduction systems:

Code: [Select]

System:    Host: delle6500 Kernel: 3.6-2.towo-siduction-amd64 x86_64 (64 bit, gcc: 4.7.2)
           Desktop: KDE 4.8.4 (Qt 4.8.2) Distro: siduction 12.1-RC1 Desperado - kde - (201205152133)
Machine:   System: Dell product: Latitude E6500
           Mobo: Dell model: 0PP476 Bios: Dell version: A14 date: 07/31/2009
CPU:       Dual core Intel Core2 Duo CPU P8600 (-MCP-) cache: 3072 KB flags: (lm nx sse sse2 sse3 sse4_1 ssse3 vmx) bmips: 9575.62
           Clock Speeds: 1: 2401.00 MHz 2: 2401.00 MHz
Graphics:  Card: NVIDIA G98M [Quadro NVS 160M] bus-ID: 01:00.0 X.Org: 1.12.4 driver: nvidia Resolution: 1920x1200@60.0hz
           GLX Renderer: Quadro NVS 160M/PCIe/SSE2 GLX Version: 3.3.0 NVIDIA 304.48 Direct Rendering: Yes
Network:   Card-1: Broadcom BCM4312 802.11b/g LP-PHY driver: b43-pci-bridge bus-ID: 0c:00.0
           IF: wlan0 state: up mac: 00:23:4e:ab:86:7a
           Card-2: Intel 82567LM Gigabit Network Connection driver: e1000e ver: 2.0.0-k port: efe0 bus-ID: 00:19.0
           IF: eth1 state: down mac: 00:21:70:d4:d3:04
Drives:    HDD Total Size: 120.0GB (36.7% used) 1: model: OCZ_VERTEX
Info:      Processes: 179 Uptime: 1:30 Memory: 957.4/3948.5MB Runlevel: 5 Gcc sys: 4.7.2 Client: Shell inxi: 1.8.19

Code: [Select]

System:    Host: tosh205 Kernel: 3.6-2.towo-siduction-686 i686 (32 bit, gcc: 4.7.2)
           Desktop: LXDE (Openbox 3.5.0) Distro: siduction 12.1 Desperado - lxde - (201205212227)
Machine:   System: TOSHIBA product: TOSHIBA NB205 version: PLL20U-00201D
           Mobo: TOSHIBA model: KAVAA version: 1.00 Bios: TOSHIBA version: V1.90 date: 01/15/2010
CPU:       Single core Intel Atom CPU N280 (-HT-) cache: 512 KB flags: (nx sse sse2 sse3 ssse3) bmips: 3325.08
           Clock Speeds: 1: 1000.00 MHz 2: 1000.00 MHz
Graphics:  Card: Intel Mobile 945GSE Express Integrated Graphics Controller bus-ID: 00:02.0
           X.Org: 1.12.4 drivers: intel (unloaded: fbdev,vesa) Resolution: 1024x600@60.0hz
           GLX Renderer: Mesa DRI Intel 945GME x86/MMX/SSE2 GLX Version: 1.4 Mesa 8.0.4 Direct Rendering: Yes
Network:   Card-1: Atheros AR9285 Wireless Network Adapter (PCI-Express) driver: ath9k bus-ID: 03:00.0
           IF: wlan0 state: up mac: 00:23:08:96:77:a1
           Card-2: Realtek RTL8101E/RTL8102E PCI Express Fast Ethernet controller
           driver: r8169 ver: 2.3LK-NAPI port: 2000 bus-ID: 04:00.0
           IF: eth0 state: down mac: 00:23:5a:fa:a0:32
Drives:    HDD Total Size: 48.1GB (13.5% used) 1: model: OCZ
           2: model: Multi
Info:      Processes: 125 Uptime: 7 min Memory: 106.0/2016.8MB Runlevel: 5 Gcc sys: 4.7.2 Client: Shell inxi: 1.8.19

Both mounted automatically as expected.

It must be an issue specific to your hardware -- if you post the output of "inxi -v3" maybe towo can see something special about it.

[krellaan]

Here the data of the system without SDHC detection. The only difference is the kernel. Detection is running with kernel 3.5-x.

Code: [Select]

System:    Host: sid Kernel: 3.6-2.towo-siduction-686 i686 (32 bit, gcc: 4.7.2)
           Desktop: KDE 4.8.4 (Qt 4.8.2) Distro: sidux 2009-03 Μώμος - kde-full - (200911110039)
Machine:   Mobo: ASUSTeK model: M70Vm version: 1.0 serial: BSN12345678901234567
           Bios: American Megatrends version: 207.000 date: 07/22/2008
CPU:       Dual core Intel Core2 Duo CPU P8600 (-MCP-) cache: 3072 KB flags: (lm nx sse sse2 sse3 sse4_1 ssse3 vmx) bmips: 9576.86
           Clock Speeds: 1: 2401.00 MHz 2: 2401.00 MHz
Graphics:  Card: NVIDIA G96 [GeForce 9600M GS] bus-ID: 01:00.0
           X.org: 1.12.4 driver: nvidia tty size: 146x42 Advanced Data: N/A for root
Network:   Card-1: Intel WiFi Link 5100 driver: iwlwifi ver: in-tree: bus-ID: 03:00.0
           IF: wlan0 state: down mac: 00:16:ea:80:49:c2
           Card-2: Realtek RTL8111/8168B PCI Express Gigabit Ethernet controller
           driver: r8169 ver: 2.3LK-NAPI port: e800 bus-ID: 06:00.0
           IF: eth0 state: up speed: 100 Mbps duplex: half mac: 00:22:15:9e:6e:3a
Drives:    HDD Total Size: 320.1GB (64.5% used) 1: model: ST9320320AS
Info:      Processes: 193 Uptime: 9:12 Memory: 1884.3/3041.5MB Runlevel: 5 Gcc sys: 4.7.2 Client: Shell inxi: 1.8.19

[hendrikL]

hi

please test following, insert the card in to the slot,
then do as root

Code: [Select]

modprobe -r sdhci_pci && modprobe sdhci_pci
a good idea would be to post the output of (or take a look to)

Code: [Select]

dmesg | tail
after inserting the card.

A good idea is also to search in the Forum for that issue

greetings hendrik

[krellaan]

That will not help.
After I have found something about it in internet it seems like there is a problem with the kernel 3.6 which may be solved with 3.7 (https://bugzilla.redhat.com/show_bug.cgi?id=748159).

Here some output on my terminal.

Code: [Select]

root@sid:/home/xxx# lsmod | grep sdhc
sdhci_pci               8591  0
sdhci                  19123  1 sdhci_pci
mmc_core               74387  2 sdhci,sdhci_pci

Code: [Select]


root@sid:/home/xxxx# dmesg | tail
[  563.422664]  [<f807c000>] ? 0xf807bfff
[  563.422667]  [<c02643ca>] ? __pci_register_driver+0x31/0x7c
[  563.422671]  [<c0101173>] ? do_one_initcall+0x7d/0x132
[  563.422674]  [<c0140e01>] ? __blocking_notifier_call_chain+0x45/0x51
[  563.422678]  [<c0165a30>] ? sys_init_module+0x130b/0x14f5
[  563.422687]  [<c03c6edf>] ? sysenter_do_call+0x12/0x28
[  563.422689] ---[ end trace 5a4a08efff64c9c3 ]---
[  563.422692] dummy: could not add device link 0000:07:01.1 err -17
[  563.422696] dummy: Failed to create debugfs directory
[  563.422699] mmc0: Hardware doesn't report any support voltages.

Code: [Select]

root@sid:/home/andreas# dmesg |grep sdhci
[    1.554347] sdhci: Secure Digital Host Controller Interface driver
[    1.554355] sdhci: Copyright(c) Pierre Ossman
[    1.554937] sdhci-pci 0000:07:01.1: SDHCI controller found [1180:0822] (rev 22)
[    1.559351] sdhci-pci 0000:07:01.1: Will use DMA mode even though HW doesn't fully claim to support it.
[  563.406474] sdhci: Secure Digital Host Controller Interface driver
[  563.406477] sdhci: Copyright(c) Pierre Ossman
[  563.421430] sdhci-pci 0000:07:01.1: SDHCI controller found [1180:0822] (rev 22)
[  563.422466] sdhci-pci 0000:07:01.1: Will use DMA mode even though HW doesn't fully claim to support it.
[  563.422491] Modules linked in: sdhci_pci(+) sdhci mmc_core cpufreq_stats cpufreq_powersave cpufreq_conservative parport_pc ppdev rfcomm bnep binfmt_misc af_packet ext3 jbd ntfs nls_utf8 nls_cp437 vfat fat lp parport dm_crypt snd_hda_codec_hdmi nvidia(PO) snd_hda_codec_realtek uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core snd_hda_intel snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss videodev snd_pcm ir_lirc_codec snd_page_alloc media lirc_dev btusb snd_seq_dummy ir_mce_kbd_decoder arc4 iwldvm snd_seq_oss snd_seq_midi snd_seq_midi_event ir_sanyo_decoder mac80211 bluetooth snd_rawmidi ir_sony_decoder snd_seq ir_jvc_decoder r592 iwlwifi ir_rc6_decoder snd_seq_device snd_timer ir_rc5_decoder joydev memstick cfg80211 snd ir_nec_decoder asus_laptop soundcore sparse_keymap rc_rc6_mce iTCO_wdt iTCO_vendor_support rfkill coretemp kvm_intel kvm evdev ite_cir rc_core acpi_cpufreq lpc_ich input_polldev video intel_agp ac battery button intel_gtt microcode psmouse pcspkr serio_raw mperf processor ext4 crc16 jbd2 mbcache dm_mod hid_generic usbhid hid sg sr_mod cdrom sd_mod crc_t10dif ahci libahci libata firewire_ohci firewire_core crc_itu_t scsi_mod r8169 mii thermal uhci_hcd ehci_hcd usbcore usb_common [last unloaded: mmc_core]
[  563.422616]  [<f80544c1>] ? sdhci_pci_enable_dma+0x5a/0x62 [sdhci_pci]
[  563.422621]  [<f804144f>] ? sdhci_add_host+0x4f6/0x98e [sdhci]
[  563.422625]  [<f8054d68>] ? sdhci_pci_probe+0x3c4/0x5b1 [sdhci_pci]


Code: [Select]

root@sid:/home/xxxx# lspci | grep SD
07:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)

[hendrikL]

please test following, insert the card in to the slot,
then do as root
modprobe -r sdhci_pci && modprobe sdhci_pci

That will not help.

Did you test it?

My sd-card reader

Code: [Select]


lspci | grep Rico
05:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
05:00.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04)
05:00.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21)


I have the same issue as you, but when i plug in the sd-card and do an modprobe (as discribet above) it works fine for me.

A little bit spam, to show thatit works!

Code: [Select]


hhl@hhl:~$ dmesg | tail                                                                                                                
[20936.167340] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X                                                                              
[20998.515258] wlan0: authenticate with 00:23:69:c3:2c:07                                                                              
[20998.515306] wlan0: send auth to 00:23:69:c3:2c:07 (try 1/3)                                                                        
[20998.518037] wlan0: authenticated
[20998.518223] iwl4965 0000:03:00.0: wlan0: disabling HT due to WEP/TKIP use
[20998.527078] wlan0: waiting for beacon from 00:23:69:c3:2c:07
[20998.557025] wlan0: associate with 00:23:69:c3:2c:07 (try 1/3)
[20998.559615] wlan0: RX AssocResp from 00:23:69:c3:2c:07 (capab=0x411 status=0 aid=1)
[20998.589236] wlan0: associated
[20998.589293] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
hhl@hhl:~$ su
Password:
root@hhl:/home/hhl#  modprobe -r sdhci_pci && modprobe sdhci_pci
root@hhl:/home/hhl# lspci | grep Rico
05:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev ba)
05:00.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 04)
05:00.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 21)
root@hhl:/home/hhl# mod
modconf           modeline2fb       modinfo           modprobe          module-assistant  modutil          
root@hhl:/home/hhl# modprobe -r sd
sdhci      sdhci_pci  sd_mod    
root@hhl:/home/hhl# modprobe -r sdhci_pci
root@hhl:/home/hhl# dmesg | tail
[21620.124038] mmc0: no vmmc regulator found
[21620.125063] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[21620.125851] Registered led device: mmc0::
[21620.147096] mmc0: SDHCI controller on PCI [0000:05:00.2] using DMA
[21620.417183] mmc0: new high speed SDHC card at address b368
[21620.423343] mmcblk0: mmc0:b368 SMI   3.68 GiB
[21620.425134]  mmcblk0: p1
[22002.649165] mmc0: card b368 removed
[22002.650786] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[22002.665068] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
root@hhl:/home/hhl# dmesg | tail
[21620.124038] mmc0: no vmmc regulator found
[21620.125063] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[21620.125851] Registered led device: mmc0::
[21620.147096] mmc0: SDHCI controller on PCI [0000:05:00.2] using DMA
[21620.417183] mmc0: new high speed SDHC card at address b368
[21620.423343] mmcblk0: mmc0:b368 SMI   3.68 GiB
[21620.425134]  mmcblk0: p1
[22002.649165] mmc0: card b368 removed
[22002.650786] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[22002.665068] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
root@hhl:/home/hhl# dmesg | tail
[21620.124038] mmc0: no vmmc regulator found
[21620.125063] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[21620.125851] Registered led device: mmc0::
[21620.147096] mmc0: SDHCI controller on PCI [0000:05:00.2] using DMA
[21620.417183] mmc0: new high speed SDHC card at address b368
[21620.423343] mmcblk0: mmc0:b368 SMI   3.68 GiB
[21620.425134]  mmcblk0: p1
[22002.649165] mmc0: card b368 removed
[22002.650786] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[22002.665068] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
root@hhl:/home/hhl# modprobe -r sdhci_pci && modeprobe sdhci_pci
Could not find the database of available applications, run update-command-not-found as root to fix this
modeprobe: command not found
root@hhl:/home/hhl# modprobe -r sdhci_pci && modprobe sdhci_pci
root@hhl:/home/hhl# dmesg | tail
[22239.808153] sdhci: Copyright(c) Pierre Ossman
[22239.810031] sdhci-pci 0000:05:00.2: SDHCI controller found [1180:0822] (rev 21)
[22239.812281] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[22239.812301] mmc0: no vmmc regulator found
[22239.813327] sdhci-pci 0000:05:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
[22239.814568] Registered led device: mmc0::
[22239.838091] mmc0: SDHCI controller on PCI [0000:05:00.2] using DMA
[22240.108275] mmc0: new high speed SDHC card at address b368
[22240.108640] mmcblk0: mmc0:b368 SMI   3.68 GiB
[22240.110300]  mmcblk0: p1


Code: [Select]


inxi -v3
System:    Host: hhl.atelier.net Kernel: 3.6-3.towo-siduction-amd64 x86_64 (64 bit, gcc: 4.7.2)
           Desktop: KDE 4.8.4 (Qt 4.8.2) Distro: Debian GNU/Linux wheezy/sid
Machine:   System: LENOVO product: 7666AK7 version: ThinkPad X61s serial: L3E3897
           Mobo: LENOVO model: 7666AK7 serial: 1ZEY986A4R0 Bios: LENOVO version: 7NETB6WW (2.16 ) date: 07/01/2008
CPU:       Dual core Intel Core2 Duo CPU L7500 (-MCP-) cache: 4096 KB flags: (lm nx sse sse2 sse3 ssse3 vmx) bmips: 6383.94
           Clock Speeds: 1: 800.00 MHz 2: 800.00 MHz
Graphics:  Card: Intel Mobile GM965/GL960 Integrated Graphics Controller (primary) bus-ID: 00:02.0
           X.org: 1.12.4 drivers: intel (unloaded: fbdev,vesa) tty size: 135x44 Advanced Data: N/A for root
Network:   Card-1: Intel PRO/Wireless 4965 AG or AGN [Kedron] Network Connection
           driver: iwl4965 ver: in-tree: bus-ID: 03:00.0
           IF: wlan0 state: up mac: 00:21:5c:07:8a:a9
           Card-2: Intel 82566MM Gigabit Network Connection driver: e1000e ver: 2.0.0-k port: 1840 bus-ID: 00:19.0
           IF: eth0 state: down mac: 00:1d:72:92:b1:ed
Drives:    HDD Total Size: 350.1GB (55.0% used) 1: model: HITACHI_HTS72201
           2: model: OneTouch
Info:      Processes: 169 Uptime: 13:29 Memory: 1387.4/7918.4MB Runlevel: 5 Gcc sys: 4.7.2 Client: Shell inxi: 1.8.19


greetz hendrik

[krellaan]

I'd tested it, and many other things.
Any other ideas? :cry:

[hendrikL]

Did you insert the card before booting?
If not, test it.

As i explained above i have the same issue, no automount after inserting the sdhci card, when i do the modprobe thing it is mounted.
So i remove the card without modprobe -r,  (i click on the symbol on the desktop, safe remove or how it called), insert the card again and automounting works fine, very strange.

[ralul]

Yes the same procedure as @hendrikL I had to take with my dvbt-stick for some kernels, but then suddenly the problem vanished...

[hendrikL]

@krellan

please provide us the output of /etc/modules

what i figured out for my system, in the /etc/modules sdhci was commented out, i also added sdhci_pci, now automount works fine here.

greetz hendrikL

[krellaan]

Code: [Select]

cat /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
# Parameters can be specified after the module name.

lp
It seems empty.

[hendrikL]

Then add the cardreader section and reboot, maybe it helps.

Code: [Select]

cat /etc/modules
# /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
# Parameters can be specified after the module name.


# Generated by sensors-detect on Tue Jun  7 00:53:57 2011
# Chip drivers
coretemp

# Generated by sensors-detect on Wed Jun 29 07:05:34 2011
# Chip drivers
coretemp

# load cardreader at boottime
mmc_block
sdhci
sdhci_pci

greetz hendrikL

[krellaan]

Unfortunately it does not help.
But looks like loaded twice.

Code: [Select]

dmesg |grep sdhci
[    0.606907] sdhci: Secure Digital Host Controller Interface driver
[    0.606909] sdhci: Copyright(c) Pierre Ossman
[    0.659088] sdhci-pci 0000:07:01.1: SDHCI controller found [1180:0822] (rev 22)
[    0.660133] sdhci-pci 0000:07:01.1: Will use DMA mode even though HW doesn't fully claim to support it.
[  278.702276] sdhci: Secure Digital Host Controller Interface driver
[  278.702286] sdhci: Copyright(c) Pierre Ossman
[  278.703042] sdhci-pci 0000:07:01.1: SDHCI controller found [1180:0822] (rev 22)
[  278.704084] sdhci-pci 0000:07:01.1: Will use DMA mode even though HW doesn't fully claim to support it.
[  278.704112] Modules linked in: sdhci_pci(+) sdhci cpufreq_stats cpufreq_powersave cpufreq_conservative parport_pc ppdev rfcomm bnep binfmt_misc af_packet ext3 jbd ntfs nls_utf8 nls_cp437 vfat fat mmc_block lp parport dm_crypt nvidia(PO) uvcvideo videobuf2_vmalloc videobuf2_memops videobuf2_core videodev snd_hda_codec_hdmi media snd_hda_codec_realtek snd_hda_intel snd_hda_codec snd_hwdep ir_lirc_codec lirc_dev ir_mce_kbd_decoder ir_sanyo_decoder snd_pcm_oss snd_mixer_oss snd_pcm ir_sony_decoder snd_page_alloc arc4 snd_seq_dummy snd_seq_oss snd_seq_midi snd_seq_midi_event ir_jvc_decoder ir_rc6_decoder joydev snd_rawmidi iwldvm mac80211 snd_seq ir_rc5_decoder r592 ir_nec_decoder snd_seq_device snd_timer snd memstick btusb bluetooth rc_rc6_mce iTCO_wdt iwlwifi cfg80211 psmouse asus_laptop soundcore sparse_keymap coretemp rfkill serio_raw kvm_intel kvm ite_cir rc_core intel_agp pcspkr evdev acpi_cpufreq iTCO_vendor_support input_polldev video lpc_ich microcode intel_gtt ac battery button mperf processor ext4 crc16 jbd2 mbcache dm_mod hid_generic usbhid hid sg sr_mod sd_mod cdrom crc_t10dif firewire_ohci mmc_core firewire_core crc_itu_t thermal ahci libahci libata r8169 mii scsi_mod uhci_hcd ehci_hcd usbcore usb_common [last unloaded: sdhci]
[  278.704251]  [<f83874c1>] ? sdhci_pci_enable_dma+0x5a/0x62 [sdhci_pci]
[  278.704255]  [<f805044f>] ? sdhci_add_host+0x4f6/0x98e [sdhci]
[  278.704259]  [<f8387d68>] ? sdhci_pci_probe+0x3c4/0x5b1 [sdhci_pci]