Siduction Forum
Siduction Forum => Hardware - Support => Topic started by: bastel on 2015/07/07, 00:28:47
-
Hallo.
Ich habe hier eine 3 TB Festplatte welche in zwei Partitionen aufgeteilt ist.
Die erste wird nicht mehr erkannt.
Unter Krusader kommt folgende Fehlermeldung:
Beim Zugriff auf „1,4 TiB diesunddas (ntfs)“ ist ein Fehler aufgetreten, die Systemnachricht
lautet:
An unspe kommt cified error has occurred: Did not receive a reply. Possible causes include:
the remote application did not send a reply, the message bus security policy blocked the
reply, the reply timeout expired, or the network connection was broken.
smartctr sagt mir folgendes:
smartctl -t short /dev/sdb
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-4.0.5-towo.1-siduction-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
Read Device Identity failed: scsi error aborted command
A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options.
Kann mir bitte jemand einen Tipp geben was ich noch machen kann um an die Daten auf der ersten Partition zu kommen.
gruss bastel
-
Hi bastel,
was sagt ein ausführlicher Test von smartctl?
-
Die 2. Partition, wenn sie noch ansprechbar ist, würde ich zuerst einmal sichern, bevor ich irgendwas anderes machte.
fdisk -l zeigt die Partition noch an ? Wenn nicht versuchen mit testdisk wiederherzustellen. Wenn ja, ausbauen und mit usb adapter an einen Windowsrechner hängen, wegen NTFS wenn ich das richtig gelesen habe.
-
Hallo.
Hab die Platte schon ausgebaut und versuchte per usb darauf zuzugreifen.
An einem Windowsrechner wird die erste partition auch nicht richtig erkannt.
Heut Abend mach ich mal ein Test mit smartctl.
Das merkwürdige ist das eine andere festplatte im selben rechner auch zeitgleich ausgefallen ist. Darauf ist nur eine Partition welche nun auch nicht mehr erkannt wird.
gruss bastel
-
hallo.
also smartctl sagt folgendes:
smartctl -a /dev/sdb
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-4.0.5-towo.1-siduction-amd64] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF, SATA 6Gb/s)
Device Model: WDC WD30EZRX-00DC0B0
Serial Number: WD-WMC1T0311466
LU WWN Device Id: 5 0014ee 058c0f7fd
Firmware Version: 80.00A80
User Capacity: 3.000.592.982.016 bytes [3,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Wed Jul 8 06:05:05 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: (42120) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 422) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70b5) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 373
3 Spin_Up_Time 0x0027 176 171 021 Pre-fail Always - 6175
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1006
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 7427
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 915
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 31
193 Load_Cycle_Count 0x0032 196 196 000 Old_age Always - 14190
194 Temperature_Celsius 0x0022 124 106 000 Old_age Always - 26
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 199 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0030 200 199 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 198 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 7427 366285376
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
gruss bastel
-
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 373
und
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 7427 366285376
sagen eigentlich schon alles:
Da der LBA offset gegeben ist, liegt es höchstwahrscheinlich nicht am sata-kabel oder dem sata-chip auf dem mainboard... Da ist die Platte selbst angeschlagen.
-
naja schön das es wahrscheinlich nicht am mainboard liegt, nur das könnte man ja ersetzten.
....
was könnte ich versuchen um nochmal an die daten zu kommen?
bastel
-
man könnte versuchen die partition per dd irgendwohin als image zu backuppen...
kannst du die partition read-only mounten?
gibt es nicht irgendwelche Windows Tools, die NTFS partitionen reparieren können?
-
gibt es nicht irgendwelche Windows Tools, die NTFS partitionen reparieren können?
Warum nicht TestDisk?
http://www.cgsecurity.org/wiki/TestDisk_DE
-
Evtl. hilft auch das dd_rescue Tool.
-
danke erstmal für eure tipps.
gruss bastel
-
Hallo.
Also ich hab mit dd if=/dev/sdX of=/dev/sdY bs=256 conv=noerror,sync
die Kaputte Platte auf eine Neue gespiegelt. Hier noch ein paar Infos. (http://"https://wiki.archlinux.org/index.php/Disk_cloning#Cloning_an_entire_hard_disk")
Es waren 3 TB und hat 3-4 Tage gedauert.
Danach konnte ich zum Glück ohne Problem auf meine Daten zugreifen.
Bin mit einem riesen Schreck davon gekommen und werde mich nun intensiv mit Backup-Lösungen befassen.
Was kann man mit der Festplatte mit Lesefehlern machen - gibts ne möglichkeit diese zu reparieren?
Viele Grüße bastel
-
es gibt für die defekte platte eher nur eine lösung: mit nullen überschreiben, physisch zerstören und entsorgen.
-
Hi bastel,
ich kann dir bzgl. Backup einen Tipp geben. rsnapshot ist ein ideales (Commandline)Tool um platzsparend dateibasierte Backups in beliebig vielen Version zu erstellen. Idealerweise würde ich den Backup auf einen 2-Disk-NAS via NFS ablegen. Das hat sich bei mir seit Jahren bewährt und funktioniert sehr zuverlässig.
-
2-Disk-NAS wegen Raid1 und höherer Sicherheit?
-
Hallo.
Tja schade, dann werde ich die defekte Platte wohl oder über vernichten (ist grade mal 2,5 Jahre alt - toll bei 2 Jahren Garantie).
Habe mir nun als Backup-Programm "back in time" eingerichtet.
Klappt gut und unkompliziert.
Bis dann bastel.