Siduction Forum
Siduction Forum => Upgrade Warnings => Topic started by: ReinerS on 2019/07/10, 22:59:39
-
Hallo,kann es sein dass Kernel 5.2 noch keine dvb-Unterstützung bzw. Module hat?Habe den aktuellen von exp. mal installiert, keine DVB Eingänge erkannt.
Mit Kernel 5.1.16 problemlos.
Hello,could it be the case that Kernel 5.2 not/not yet supports dvb-inputs or Modules?
Installed the actual 5.2 Kernel from exp, no dvb-inputs are found.
Started Kernel 5.1.16 again, no problems.
regards
Reiner
-
Ja, das sieht wohl so aus, muss ich beim näxten build fixen.
-
So, neuer 5.2er Kernel ist im Repo, da habe ich so ziemlich alles, was DVB ist, aktiviert.
-
Danke, lade ich wenn ich wieder ordentliches Internet habe. Bin aktuell ziemlich offline.
Grüße
Reiner
-
Hallo, habe seit gestern wieder Internet (Glasfaser) und mit dem aktuellen d-u den Kernel 5.2.5-towo-3 bekommen.
Dvb geht prinzipiell, aber das Modul für Conextant CX24117/24132 (Karte mit 2 Tunern, ) werden nicht geladen. Das Modul für CX 24120/24118 (Techsan Co B2C2 FlexCopII DVB chip /Technisat Skystar 2) wird aber erkannt und betrieben.
Mit dem Kernel 5.1.16-towo-1 funktionieren sämtliche Karten/Tuner normal.
Grüße
Reiner
-
~
towo:Defiant> grep CX24 /boot/config-5.2.5-towo.3-siduction-amd64
# CONFIG_ENCX24J600 is not set
CONFIG_DVB_CX24110=m
CONFIG_DVB_CX24123=m
CONFIG_DVB_TUNER_CX24113=m
CONFIG_DVB_CX24116=m
CONFIG_DVB_CX24117=m
CONFIG_DVB_CX24120=m
Mehr kann ich ohne weitere Infos nicht tun.
-
@towo: Was genau brauchst du ? Ich kann das Modell und den Original-Hersteller feststellen. Reicht das ?
Das zeigt lspci:04:07.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card (rev 02)
05:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885 PCI Video and Audio Decoder (rev 04)
Sollte diese Karte sein: TBA 6981 Dual DVB S2 SAT-TV-Empfängerkarte mit zwei Tunern von TBS.
Firmware war bisher ok.
Grüße
Reiner
-
Moin Gemeinde :)
Erstmal möchte ich mich kurz vorstellen, bin dabei seit Kanotix, vorher SuSE und Mandrake. Bei Sidux war ich schon mal angemeldet als 'guzzel', ...und habe seitdem eure gute Arbeit einfach klammheimlich genutzt... ;)
Nun zum Problem, genau wie bei ReinerS funktioniert meine DVBS-Karte nur noch mit Kernel4.x. Es ist folgendes Modell https://linuxtv.org/wiki/index.php/TeVii_S470 .
Die Technisat Skystar-S2 USB am Laptop funktioniert astrein :D
Towo, wenn du weitere Information brauchst, sag bitte welche, die bekommst du dann...
beste Grüße vom boerni
-
Ich kann nur ab und an über kaffeine mich beklagen, sonst ist hier alles ok. :D
inxi -SNxxx
System: Host: sidukde Kernel: 5.2.5-towo.5-siduction-amd64 x86_64 bits: 64 compiler: gcc v: 9.1.0
Desktop: KDE Plasma 5.14.5 tk: Qt 5.11.3 wm: kwin_x11 dm: LightDM 1.26.0
Distro: siduction 16.1.0 Patience - kde - (201702251051) base: Debian GNU/Linux bullseye/sid
Network: Device-1: Qualcomm Atheros AR8121/AR8113/AR8114 Gigabit or Fast Ethernet vendor: ASUSTeK driver: ATL1E
v: N/A port: cc00 bus ID: 02:00.0 chip ID: 1969:1026
Device-2: Techsan Co B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card driver: b2c2_flexcop_pci
v: kernel port: ec00 bus ID: 05:01.0 chip ID: 13d0:2103
-
@unklarer: die Technisat SkyStar2 tut ja auch hier brav, nur die andere halt nicht.
Wobei ich auf dem "Heimserver" tvheadend zum Aufnehmen nutze. Kaffeine nur gelegentlich wenns mal Probleme zu checken gibt.
Grüße
Reiner
-
Naja, ich bräuchte zumindest die Info, welche Module geladen sind und was dmesg so zu der hardware sagt.
-
Habe gerade kernel 5.2.5 reingekriegt, gleiches Problem.Ich poste gleich mal die Liste mit den Modulen von Kernel 5.1.16.
Grüße
Reiner
-
So, im Anhang die komplette lsmod-Liste und von dmesg die Ausgabe von "dmesg|grep dvb".
Hoffe das hilft etwas weiter.
Grüße
Reiner
-
Ja, ich muß auch korrigieren, bis Kernel 5.1.19 funktioniert die Karte. mit folgender Ausgabe:
boerni@tuxbox:~$ dmesg | grep -i dvb
[ 2.726336] cx23885: cx23885_dvb_register() allocating 1 frontend(s)
[ 2.726338] cx23885: cx23885[0]: cx23885 based dvb card
[ 2.795755] dvbdev: DVB: registering new adapter (cx23885[0])
[ 2.795757] cx23885 0000:05:00.0: DVB: registering adapter 0 frontend 0 (Montage Technology DS3000)...
[ 59.391988] ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
[ 59.392333] cx23885 0000:05:00.0: firmware: direct-loading firmware dvb-fe-ds3000.fw
[ 115.061955] ds3000_firmware_ondemand: Waiting for firmware upload (dvb-fe-ds3000.fw)...
[ 115.061987] cx23885 0000:05:00.0: firmware: direct-loading firmware dvb-fe-ds3000.fw
Ab 5.2 ohne Ausgabe
lsmod sagt (unter 5.1.19):root@tuxbox:/home/boerni# lsmod
Module Size Used by
rfcomm 49152 16
af_packet 53248 0
cmac 16384 0
bnep 20480 2
cpufreq_conservative 16384 0
cpufreq_powersave 16384 0
nls_utf8 16384 1
nls_cp437 20480 1
vfat 20480 1
fat 81920 1 vfat
ts2020 20480 1
ds3000 24576 1
snd_hda_codec_hdmi 57344 1
intel_rapl 24576 0
x86_pkg_temp_thermal 16384 0
intel_powerclamp 16384 0
coretemp 16384 0
uas 28672 0
cx23885 184320 0
tda18271 49152 1 cx23885
videobuf2_dvb 16384 1 cx23885
usb_storage 61440 1 uas
kvm_intel 286720 0
m88ds3103 24576 1 cx23885
mei_hdcp 20480 0
uvcvideo 110592 0
tveeprom 24576 1 cx23885
kvm 458752 1 kvm_intel
snd_hda_codec_realtek 94208 1
irqbypass 16384 1 kvm
i915 1933312 24
cx2341x 32768 1 cx23885
btusb 49152 0
snd_usb_audio 212992 2
joydev 24576 0
dvb_core 131072 3 m88ds3103,cx23885,videobuf2_dvb
btrtl 16384 1 btusb
snd_usbmidi_lib 28672 1 snd_usb_audio
btbcm 16384 1 btusb
snd_rawmidi 32768 1 snd_usbmidi_lib
videobuf2_vmalloc 16384 2 uvcvideo,dvb_core
intel_cstate 16384 0
snd_hda_codec_generic 77824 1 snd_hda_codec_realtek
i2c_algo_bit 16384 1 i915
intel_rapl_perf 16384 0
btintel 20480 1 btusb
snd_seq_device 16384 1 snd_rawmidi
ledtrig_audio 16384 2 snd_hda_codec_generic,snd_hda_codec_realtek
drm_kms_helper 172032 1 i915
bluetooth 434176 41 btrtl,btintel,btbcm,bnep,btusb,rfcomm
rc_core 40960 1 cx23885
evdev 20480 13
pcspkr 16384 0
ecdh_generic 24576 1 bluetooth
v4l2_common 16384 2 cx2341x,cx23885
rfkill 24576 6 bluetooth
snd_hda_intel 32768 6
i2c_mux 16384 1 m88ds3103
videobuf2_dma_sg 16384 1 cx23885
snd_hda_codec 118784 4 snd_hda_codec_generic,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_realtek
drm 409600 11 drm_kms_helper,i915
videobuf2_memops 16384 2 videobuf2_vmalloc,videobuf2_dma_sg
snd_hda_core 65536 5 snd_hda_codec_generic,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec,snd_hda_codec_realtek
videobuf2_v4l2 24576 2 uvcvideo,cx23885
sg 36864 0
snd_hwdep 16384 2 snd_usb_audio,snd_hda_codec
videobuf2_common 45056 5 videobuf2_v4l2,uvcvideo,dvb_core,cx23885,videobuf2_dvb
intel_gtt 24576 1 i915
snd_pcm 98304 6 snd_hda_codec_hdmi,snd_hda_intel,snd_usb_audio,snd_hda_codec,cx23885,snd_hda_core
videodev 188416 6 cx2341x,v4l2_common,videobuf2_v4l2,uvcvideo,videobuf2_common,cx23885
iTCO_wdt 16384 0
syscopyarea 16384 1 drm_kms_helper
snd_timer 32768 1 snd_pcm
mei_me 24576 1
media 40960 5 videodev,videobuf2_v4l2,uvcvideo,dvb_core,videobuf2_common
snd 81920 29 snd_hda_codec_generic,snd_seq_device,snd_hda_codec_hdmi,snd_hwdep,snd_hda_intel,snd_usb_audio,snd_usbmidi_lib,snd_hda_codec,snd_hda_codec_realtek,snd_timer,cx23885,snd_pcm,snd_rawmidi
regmap_i2c 16384 2 m88ds3103,ts2020
sysfillrect 16384 1 drm_kms_helper
mei 77824 3 mei_hdcp,mei_me
sysimgblt 16384 1 drm_kms_helper
iTCO_vendor_support 16384 1 iTCO_wdt
fb_sys_fops 16384 1 drm_kms_helper
soundcore 16384 1 snd
button 16384 0
pcc_cpufreq 16384 0
cuse 16384 0
fuse 122880 4 cuse
loop 32768 0
parport_pc 49152 1
ppdev 20480 0
lp 20480 0
parport 49152 3 parport_pc,lp,ppdev
sunrpc 258048 1
ip_tables 28672 0
x_tables 36864 1 ip_tables
autofs4 36864 2
hid_generic 16384 0
usbhid 49152 0
hid 126976 2 usbhid,hid_generic
ext4 479232 2
crc16 16384 2 bluetooth,ext4
mbcache 16384 1 ext4
jbd2 86016 1 ext4
btrfs 1150976 0
zstd_decompress 81920 1 btrfs
zstd_compress 180224 1 btrfs
raid10 61440 0
raid456 143360 0
async_raid6_recov 20480 1 raid456
async_memcpy 16384 2 raid456,async_raid6_recov
async_pq 16384 2 raid456,async_raid6_recov
async_xor 16384 3 async_pq,raid456,async_raid6_recov
async_tx 16384 5 async_pq,async_memcpy,async_xor,raid456,async_raid6_recov
xor 24576 2 async_xor,btrfs
raid6_pq 118784 4 async_pq,btrfs,raid456,async_raid6_recov
libcrc32c 16384 2 btrfs,raid456
crc32c_generic 16384 0
raid1 49152 0
raid0 20480 0
multipath 16384 0
linear 16384 0
md_mod 143360 6 raid1,raid10,raid0,linear,raid456,multipath
sr_mod 28672 0
sd_mod 53248 5
cdrom 36864 1 sr_mod
crct10dif_pclmul 16384 1
crc32_pclmul 16384 0
crc32c_intel 24576 4
ghash_clmulni_intel 16384 0
ahci 40960 3
xhci_pci 16384 0
libahci 36864 1 ahci
ehci_pci 16384 0
aesni_intel 372736 0
xhci_hcd 163840 1 xhci_pci
ehci_hcd 57344 1 ehci_pci
aes_x86_64 20480 1 aesni_intel
libata 208896 2 libahci,ahci
crypto_simd 16384 1 aesni_intel
i2c_i801 28672 0
lpc_ich 28672 0
scsi_mod 188416 6 sd_mod,usb_storage,uas,libata,sg,sr_mod
i2c_core 53248 16 tda18271,videodev,i2c_mux,drm_kms_helper,v4l2_common,i2c_algo_bit,m88ds3103,tveeprom,dvb_core,i2c_i801,ts2020,cx23885,ds3000,i915,regmap_i2c,drm
mfd_core 16384 1 lpc_ich
cryptd 20480 3 crypto_simd,ghash_clmulni_intel,aesni_intel
glue_helper 16384 1 aesni_intel
r8169 81920 0
realtek 20480 1
usbcore 225280 11 xhci_hcd,ehci_pci,snd_usb_audio,usbhid,snd_usbmidi_lib,usb_storage,uvcvideo,ehci_hcd,btusb,xhci_pci,uas
fan 16384 0
thermal 20480 0
video 40960 1 i915
beste Grüße vom Bernd
-
Hm, lsmod zeigt m.W. aber nur die geladenen Module an.
Ergo müßtet Ihr mal schauen, wie denn das/die Module eurer Karten lauten und dann auf depends achten.
Hier das Beispiel meiner Karte
modinfo b2c2-flexcop
filename: /lib/modules/5.2.5-towo.5-siduction-amd64/kernel/drivers/media/common/b2c2/b2c2-flexcop.ko
license: GPL
description: B2C2 FlexcopII/II(b)/III digital TV receiver chip
author: Patrick Boettcher <patrick.boettcher@posteo.de
depends: s5h1420,dvb-core,cx24113,cx24123 <---
retpoline: Y
intree: Y
name: b2c2_flexcop
vermagic: 5.2.5-towo.5-siduction-amd64 SMP preempt mod_unload modversions
parm: debug:set debug level (1=info,2=tuner,4=i2c,8=ts,16=sram,32=reg,64=i2cdump (|-able)). (debugging is not enabled) (int)
parm: adapter_nr:DVB adapter numbers (array of short)
modinfo b2c2-flexcop_pci
filename: /lib/modules/5.2.5-towo.5-siduction-amd64/kernel/drivers/media/pci/b2c2/b2c2-flexcop-pci.ko
license: GPL
description: flexcop-pci
author: Patrick Boettcher <patrick.boettcher@posteo.de>
alias: pci:v000013D0d00002103sv*sd*bc*sc*i*
depends: b2c2-flexcop
retpoline: Y
intree: Y
name: b2c2_flexcop_pci
vermagic: 5.2.5-towo.5-siduction-amd64 SMP preempt mod_unload modversions
parm: enable_pid_filtering:enable hardware pid filtering: supported values: 0 (fullts), 1 (int)
parm: irq_chk_intv:set the interval for IRQ streaming watchdog. (int)
parm: debug:set debug level (1=info,2=regs,4=TS,8=irqdma,16=check (|-able)). (debugging is not enabled) (int)
Erst, wenn "depends" "erfüllt" ist, wird das richtige Modul korrekt geladen.
-
Ausgaben vom 5.1 nützen mir nicht viel. Ein Anfang wäre mal ein manuelles modprobe der benötigten Module, wenn diese nicht automatisch geladen werden.
Und btw, ein Besuch im IRC würde das Ganze etwas beschleunigen, weil man dort in Echtzeit kommunizieren kann.
-
Danke towo und unklarer
jetzt mit Kernel 5.2.5
root@tuxbox:/home/boerni# modinfo ds3000
filename: /lib/modules/5.2.5-towo.5-siduction-amd64/kernel/drivers/media/dvb-frontends/ds3000.ko
firmware: dvb-fe-ds3000.fw
license: GPL
author: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
description: DVB Frontend module for Montage Technology DS3000 hardware
depends:
retpoline: Y
intree: Y
name: ds3000
vermagic: 5.2.5-towo.5-siduction-amd64 SMP preempt mod_unload modversions
parm: debug:Activates frontend debugging (default:0) (int)
da haben wir's; die depends sind leer...
beste Grüße vom Bernd
P.S. Danke towo , da werde ich euch bestimmt auch aufsuchen, jetzt muß ich erstmal in die Arbeit...
-
Jetzt mit Kernel 5.2.5.
Kann es sein dass das Modul cx23885, das bei Kernel 5.1.16 noch drin ist bei 5.2.5 fehlt oder weggefallen ist?
root@VdrLX:/lib/modules# find . -name "cx23885*"
./5.1.16-towo.1-siduction-amd64/kernel/drivers/media/pci/cx23885
./5.1.16-towo.1-siduction-amd64/kernel/drivers/media/pci/cx23885/cx23885.ko
Grüße
Reiner
-
~
towo:Defiant> grep -i cx23 /boot/config-5.2.6-towo.1-siduction-amd64
CONFIG_VIDEO_CX231XX=m
CONFIG_VIDEO_CX231XX_RC=y
CONFIG_VIDEO_CX231XX_ALSA=m
CONFIG_VIDEO_CX231XX_DVB=m
CONFIG_VIDEO_CX23885=m
CONFIG_VIDEO_CX2341X=m
CONFIG_VIDEO_CX23885=m hatte ich tatsächlich vergessen.
-
ok, probiere ich gleich aus.
Grüße
Reiner
-
Ja, das wars. Alle 3 Eingänge funktionieren jetzt einwandfrei bei mir.Vielen Dank !
Grüße
Reiner
-
Ok, danke für die Bestätigung.
-
Danke towo !
Genau Das war's ! - mit Kernel 5.2.6 läuft es wieder...
beste Grüße vom boerni
P,S, verzeih bitte daß ich dich mit Kernel 5.1 genervt hatte, bin halt der Vize-DAU