Hallo,
ich bin gerade dabei mich mit dem Laptop vom Kabelnetzwerk zu lösen, nur leider wird die Funknetzwerkkarte leider nicht gefunden
ifconfig
eth0 Link encap:Ethernet Hardware Adresse 00:02:3f:18:db:e6
inet Adresse:192.168.178.21 Bcast:192.168.178.255 Maske:255.255.255.0
inet6-Adresse: fe80::202:3fff:fe18:dbe6/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX Pakets:149867 errors:0 dropped:0 overruns:0 frame:0
TX packets:85460 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:215622288 (205.6 MiB) TX bytes:6209533 (5.9 MiB)i
lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:65536 Metrik:1
RX packets:74 errors:0 dropped:0 overruns:0 frame:0
TX packets:74 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:5956 (5.8 KiB) TX bytes:5956 (5.8 KiB)
root@siductionbox:/home/mgtd# inxi -AG
Graphics: Card: Advanced Micro Devices [AMD/ATI] RV350/M10 [Mobility Radeon 9600 PRO Turbo]
Display Server: X.org 1.16.0 drivers: ati,radeon (unloaded: fbdev,vesa)
tty size: 128x21 Advanced Data: N/A for root
Audio: Card Intel 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller driver: snd_intel8x0
Sound: Advanced Linux Sound Architecture v: k3.16-1.towo-siduction-686
root@siduct
[code]
ich habe auch schon
[code]apt-get install firmware-linux firmware-linux-free firmware-linux-nonfree
[code]installiert
Was sagt denn inxi -n oder inxi -v2?
Wenn da nix vom Netzwerkchip kommt: lsusb oder lspci?
root@siductionbox:/home/mgtd# inxi -n
Network: Card-1: Realtek RTL-8139/8139C/8139C+ driver: 8139too
IF: eth0 state: unknown speed: 100 Mbps duplex: full mac: 00:02:3f:18:db:e6
Card-2: Intel PRO/Wireless 2200BG [Calexico2] Network Connection
IF: N/A state: N/A mac: N/A
root@siductionbox:/home/mgtd# inxi -v2
System: Host: siductionbox Kernel: 3.16-1.towo-siduction-686 i686 (32 bit) Desktop: LXDE (Openbox 3.5.2)
Distro: siduction 12.1.6 Razor-qt LU-Edition - rqt - (201206250126)
Machine: System: Acer product: TravelMate 290
Mobo: N/A model: N/A Bios: ACER v: Version 1.40.T2 date: 05/31/2004
CPU: Single core Intel Pentium M (-UP-) clocked at 1500 MHz
Graphics: Card: Advanced Micro Devices [AMD/ATI] RV350/M10 [Mobility Radeon 9600 PRO Turbo]
Display Server: X.org 1.16.0 drivers: ati,radeon (unloaded: fbdev,vesa)
tty size: 128x23 Advanced Data: N/A for root
Network: Card-1: Realtek RTL-8139/8139C/8139C+ driver: 8139too
Card-2: Intel PRO/Wireless 2200BG [Calexico2] Network Connection
Drives: HDD Total Size: 60.0GB (33.6% used) ID-1: model: HITACHI_DK23EA
Info: Processes: 131 Uptime: 16 min Memory: 308.9/501.8MB Client: Shell (bash) inxi: 2.2.1
root@siductionbox:/home/mgtd#
und eben schnell nachreich
root@siductionbox:/home/mgtd# lsusb
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
root@siductionbox:/home/mgtd# lspci
00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 21)
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 21)
00:1d.0 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 03)
00:1d.1 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 03)
00:1d.2 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 03)
00:1d.7 USB controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 83)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 03)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 03)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 03)
01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV350/M10 [Mobility Radeon 9600 PRO Turbo]
02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev 80)
02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
02:02.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
02:03.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01)
root@siductionbox:/home/mgtd#
ich hoffe, es ist hilfreich.
apt-get install firmware-ipw2x00
rebootdenn:
Zitat
apt-cache search intel 2200
firmware-ipw2x00 - Binary firmware for Intel Pro Wireless 2100, 2200 and 2915
firmware-iwlwifi - Binary firmware for Intel Wireless cards
apt-cache show firmware-ipw2x00
firmware-ipw2x00
Package: firmware-ipw2x00
Source: firmware-nonfree
Version: 0.43
Installed-Size: 1226
Maintainer: Debian Kernel Team <debian-kernel@lists.debian.org>
Architecture: all
Depends: debconf (>= 0.5) | debconf-2.0
Pre-Depends: debconf | debconf-2.0
Suggests: initramfs-tools
Description-en: Binary firmware for Intel Pro Wireless 2100, 2200 and 2915
This package contains the binary firmware for Intel Pro Wireless 2100,
2200 and 2915 cards supported by the ipw2100 and ipw2200 drivers.
.
Contents:
* Intel Pro Wireless 2100 firmware (bootstrap), version 1.3
(ipw2100-1.3.fw)
* Intel Pro Wireless 2100 firmware (ibss mode), version 1.3
(ipw2100-1.3-i.fw)
* Intel Pro Wireless 2100 firmware (monitor mode), version 1.3
(ipw2100-1.3-p.fw)
* Intel Pro Wireless 2200/2915 firmware (bss), version 3.1
(ipw2200-bss.fw)
* Intel Pro Wireless 2200/2915 firmware (ibss), version 3.1
(ipw2200-ibss.fw)
* Intel Pro Wireless 2200/2915 firmware (snf), version 3.1
(ipw2200-sniffer.fw)
root@siductionbox:/home/mgtd# apt-cache policy firmware-ipw2x00
firmware-ipw2x00:
Installiert: 0.43
Installationskandidat: 0.43
Versionstabelle:
*** 0.43 0
500 http://ftp2.de.debian.org/debian/ unstable/non-free i386 Packages
500 http://ftp.us.debian.org/debian/ unstable/non-free i386 Packages
500 http://ftp.us.debian.org/debian/ testing/non-free i386 Packages
100 /var/lib/dpkg/status
0.41 0
500 http://http.debian.net/debian/ unstable/non-free i386 Packages
root@siductionbox:/home/mgtd#
[code] funzt immer noch nicht
"Funzt nicht" hilft auch Keinem!
Hast DU nach der Installation der Firmware das Kernel-Modul neu geladen?
Wie towo sagt: Mit "funzt nicht" ist, außer in's Blaue raten, keine Hilfe möglich.
Was weiterhelfen könnte ist die Ausgabe von folgendem:
modprobe -rv ipw2200
modprobe -iv ipw2200
rfkill list
ifconfig
iwconfig
# modprobe -rv ipw2200
rmmod ipw2200
rmmod libipw
rmmod lib80211
rmmod cfg80211
rmmod rfkill
root@siductionbox:/home/mgtd#
root@siductionbox:/home/mgtd# modprobe -iv ipw2200
insmod /lib/modules/3.16-1.towo-siduction-686/kernel/net/rfkill/rfkill.ko
insmod /lib/modules/3.16-1.towo-siduction-686/kernel/net/wireless/lib80211.ko
insmod /lib/modules/3.16-1.towo-siduction-686/kernel/net/wireless/cfg80211.ko
insmod /lib/modules/3.16-1.towo-siduction-686/kernel/drivers/net/wireless/ipw2x00/libipw.ko
insmod /lib/modules/3.16-1.towo-siduction-686/kernel/drivers/net/wireless/ipw2x00/ipw2200.ko
root@siductionbox:/home/mgtd#
root@siductionbox:/home/mgtd# rfkill list
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
root@siductionbox:/home/mgtd#
root@siductionbox:/home/mgtd# ifconfig
eth0 Link encap:Ethernet Hardware Adresse 00:02:3f:18:db:e6
inet Adresse:192.168.178.21 Bcast:192.168.178.255 Maske:255.255.255.0
inet6-Adresse: fe80::202:3fff:fe18:dbe6/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:70985 errors:0 dropped:0 overruns:0 frame:0
TX packets:43422 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:101022369 (96.3 MiB) TX bytes:3430601 (3.2 MiB)
lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:65536 Metrik:1
RX packets:1770 errors:0 dropped:0 overruns:0 frame:0
TX packets:1770 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:138740 (135.4 KiB) TX bytes:138740 (135.4 KiB)
root@siductionbox:/home/mgtd#
root@siductionbox:/home/mgtd# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11bg ESSID:off/any
Mode:Managed Channel:0 Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power=20 dBm Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
root@siductionbox:/home/mgtd#
Dein Chip ist als eth1 da, sollte aber AFAIK wlan0 sein damit es funktioniert.
Zeig mal bitte die Ausgabe von cat /etc/udev/rules.d/70-persistent-net.rules
cat /etc/udev/rules.d/70-persistent-net.rules
# This file was automatically generated by the /lib/udev/write_net_rules
# program, run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.
# PCI device 0x10ec:/sys/devices/pci0000:00/0000:00:1e.0/0000:02:01.0 (8139too)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:02:3f:18:db:e6", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
# PCI device 0x8086:0x4220 (ipw2200)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0e:35:35:fa:5f", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1"
mgtd@siductionbox:~$
Öffne die Datei als root mit dem Editor Deiner Wahl und änder sie so ab:
Zitat# This file was automatically generated by the /lib/udev/write_net_rules
# program, run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.
# PCI device 0x10ec:/sys/devices/pci0000:00/0000:00:1e.0/0000:02:01.0 (8139too)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:02:3f:18:db:e6", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0"
# PCI device 0x8086:0x4220 (ipw2200)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0e:35:35:fa:5f", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="wlan*", NAME="wlan0"
Speichern/Schließen
Dann entweder ein
udevadm triggeroder ein reboot und schau dann mal ob Du mit ceni oder Networkmanager was bekommst.
Wenn nicht nochmal die Ausgabe von rfkill list, ifconfig, iwconfig. Eventuell auch noch ein
iwlist scan aber nimm dort die Zeilen raus die mit
ZitatIE: Unknown
beginnen, ich bin mir nicht sicher ob da nicht der Schlüssel mit bei ist.
iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11bg ESSID:off/any
Mode:Managed Channel:0 Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power=20 dBm Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
root@siductionbox:/home/mgtd# iwlist scan
lo Interface doesn't support scanning.
eth0 Interface doesn't support scanning.
eth1 Scan completed :
Cell 01 - Address: 08:96:D7:84:9E:06
ESSID:"FritzBox!"
Protocol:IEEE 802.11bg
Mode:Master
Frequency:2.412 GHz (Channel 1)
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality=96/100 Signal level=-30 dBm
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
Extra: Last beacon: 150ms ago
Cell 02 - Address: 2A:65:11:99:92:C3
ESSID:"MANNI_HOME"
Protocol:IEEE 802.11bg
Mode:Master
Frequency:2.437 GHz (Channel 6)
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality=53/100 Signal level=-69 dBm
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
Extra: Last beacon: 93ms ago
Cell 03 - Address: 08:96:D7:E5:1A:8D
ESSID:"Netz"
Protocol:IEEE 802.11bg
Mode:Master
Frequency:2.412 GHz (Channel 1)
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality=39/100 Signal level=-77 dBm
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
Extra: Last beacon: 213ms ago
wo steht das mit dem
IE: Unknown
ayla
Hi,
ich hab hier gerade das Läppi eines Bekannten mit dem gleichen WLAN-Chip in die Finger bekommen.
Das WLAN funktioniert nach Installation der firmware und Einschalten per Hardwareschalter auch ohne die udev-rules zu ändern. Also mach die Änderungen in den 70-persistent-net.rules bitte rückgängig -lt einigem gegoogel funktioniert das sowieso nicht (mehr).
Allerdings: Sobald Du Dein Laptop ohne Kabelverbindung bootest ändert sich Dein wlan-Interface von eth1 auf eth0, das kann etwas umständlich sein wenn Du was anderes als den NetworkManager benutzt.!
Wie -mit welcher app- verbindest Du Dich mit dem Router? NM, ceni, oder wicd?
Was sagt rfkill list nach einem Verbindungsversuch?
# modprobe -iv ipw2200
insmod /lib/modules/3.16-2.towo-siduction-686/kernel/net/rfkill/rfkill.ko
insmod /lib/modules/3.16-2.towo-siduction-686/kernel/net/wireless/lib80211.ko
insmod /lib/modules/3.16-2.towo-siduction-686/kernel/net/wireless/cfg80211.ko
insmod /lib/modules/3.16-2.towo-siduction-686/kernel/drivers/net/wireless/ipw2x00/libipw.ko
insmod /lib/modules/3.16-2.towo-siduction-686/kernel/drivers/net/wireless/ipw2x00/ipw2200.ko
root@siductionbox:/home/mgtd#
root@siductionbox:/home/mgtd# rfkill list
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
root@siductionbox:/home/mgtd#
root@siductionbox:/home/mgtd# ifconfig
eth0 Link encap:Ethernet Hardware Adresse 00:02:3f:18:db:e6
inet Adresse:192.168.178.21 Bcast:192.168.178.255 Maske:255.255.255.0
inet6-Adresse: fe80::202:3fff:fe18:dbe6/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:1411 errors:0 dropped:0 overruns:0 frame:0
TX packets:1318 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:1227694 (1.1 MiB) TX bytes:181031 (176.7 KiB)
lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:65536 Metrik:1
RX packets:64 errors:0 dropped:0 overruns:0 frame:0
TX packets:64 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:5184 (5.0 KiB) TX bytes:5184 (5.0 KiB)
root@siductionbox:/home/mgtd#
root@siductionbox:/home/mgtd# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11bg ESSID:off/any
Mode:Managed Channel:0 Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power=20 dBm Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
root@siductionbox:/home/mgtd#
[
[code]
[font=Verdana][size=78%]So sieht es mit neuem kernel aus ayla[/font][/size]
cat /etc/network/interfaces
Schlüssel aus-x-sen
Nochmal die Frage: Mit was versuchst Du die Verbindung aufzubauen? Ceni, NM, wicd....?
Wohin versuchst Du zu Verbinden? Lt. Deinem iwlist scan sind 3 Router in Reichweite. 2 davon senden auf der gleichen Frequenz, das kann ein Problem sein. Wenn Du versuchst einen der beiden zu erreichen verleg den Channel von 1 auf 11. Falls Du versuchst "Netz" zu erreichen könnte auch die Signalqualität ein Problem sein.
Der Chip funktioniert hier auf meinem geliehenen Gerät mit den beiden letzten Kerneln problemlos, also vermute ich ein Konfigurations- oder Problem mit der Verbindungsqualität.
Gruß
ayla
cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
allow-hotplug eth0
iface eth0 inet dhcp
iface TGszd23666 inet dhcp
[code]
also, eigentlich versuche ich es über wicd und
[code]# /usr/sbin/wpa_gui
Ich kann mir beim besten Willen kein Interface vorstellen das "TGsz"-irgendwas heisst...
Tu mir einen Gefallen und öffne mal "ceni"; ist AFAIK bei jedem siduction Flavor vorinstalliert.
Erscheint dort "eth1" zur Auswahl? -> wählen -> scan -> erscheint die ESSID deines Routers? -> wenn nicht -> lesen was ceni da sagt und ausführen -> ceni neu starten und nochmal scannen. -> Pre-shared Key eingeben (Dein WPA-Passwort) -> accept -> dhcp und auto wählen -> accept
Mitteilen was ceni dazu zu sagen hat.
Zitat von: ayla in 2014/09/10, 04:42:43
Ich kann mir beim besten Willen kein Interface vorstellen das "TGsz"-irgendwas heisst...
Etwas OT zum eigentlichen Problem, aber mit systemd können (in anderen Distros als Debian (https://wiki.archlinux.org/index.php/Network#Device_names) schon länger) die sogenannten Freedesktop Predictable Interface Names (http://www.freedesktop.org/wiki/Software/systemd/PredictableNetworkInterfaceNames/) kommen, dann wär auch TGsz-irgendwas denkbar :). Soweit ich mich erinnere wollte Debian das aber per geeigneter udev-Regeln erstmal zurückhalten damit wir die gewohnten eth/wlan angezeigt kriegen. Ob und wie da sowas bei susa reingerutscht ist oder warum das in die /e/n/interfaces kam kann ich nicht einschätzen.
Was das System im Moment an Netzdevices kennt zeigt übrigens ganz kurz auch ein
ls /sys/class/net
oder auch
ip l (<--- kleines "L" für list)
Klingt gut, und wäre auch -wie dort gesagt- eine Antwort auf das eth1 -> eth0 Problem. Gutes Wiki, außerdem.
Hmm... selbst wenn da irgendwas an der Konfig bei Susa so verrutscht wäre daß dies "TGsz..." ein "Rückstand" von einem Versuch mit diesen "Predictable Interface Names" wäre, es würde immer noch die "auto" oder "hotplug"-Zeile fehlen...
Aber gut um's mal im Hinterkopf zu behalten, das aus dieser Richtung auch irgend was im Argen liegen könnte.
[size=78%][/code][~$ ls /sys/class/net
eth0 eth1 lo
mgtd@siductionbox:~$ ip l
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 1000
link/ether 00:02:3f:18:db:e6 brd ff:ff:ff:ff:ff:ff
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 00:0e:35:35:fa:5f brd ff:ff:ff:ff:ff:ff
mgtd@siductionbox:~$
[[/size][/size][/font]