Als erstes möchte ich bitte bitte den Spruch nicht hören das ich mich als noob nicht an sid halten sollte ^^
mein problem ist das sowohl lan (realtek) als auch wlan (deutlich wichtiger da ich keine kabel liegen habe ^^ - broadcom .... ist ein airport aus meinem alten macbook)
nun wurd ich (bisher nur ubuntu mint und den kram benutzt) bei der installation zum ersten mal darauf hingewiesen das ich die firmware fürs lan brauche .... auf ner sd karte die debs(pauschal alle non frees inkl dem realtek) rübergewurfen dpkg -i *.deb (jaja holzhammer) --> keine meldung mehr das ne firmware fehlen würde --> installation
nunja jetzt find ich keine netzwerkinterfaces und steh ziemlich aufm schlauch, da ich wie gesagt eher ein noob bin ^^
lspci
das als Allererstes mal.
@melchior:~$ lspci
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12)
00:01.0 PCI bridge: Intel Corporation Core Processor PCI Express x16 Root Port (rev 12)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:1a.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06)
00:1c.3 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 4 (rev 06)
00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 06)
00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06)
00:1d.0 USB Controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6)
00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06)
00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller (rev 06)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06)
02:00.0 VGA compatible controller: ATI Technologies Inc M92 [Mobility Radeon HD 4500 Series]
02:00.1 Audio device: ATI Technologies Inc RV710/730
03:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01)
06:00.0 SD Host controller: Ricoh Co Ltd MMC/SD Host Controller (rev 01)
06:00.1 System peripheral: Ricoh Co Ltd Memory Stick Host Controller (rev 01)
06:00.2 System peripheral: Ricoh Co Ltd Device e852 (rev 01)
06:00.3 FireWire (IEEE 1394): Ricoh Co Ltd FireWire Host Controller (rev 01)
08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02)
ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02)
ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02)
ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
EDIT von Moderator bluelupo. Bitte bei Postings von Kommandoausgaben code-Tags benutzen.
Also der Atheros sollte eigentlich ootb funktionieren, was meint ceni denn?
ach gucke einer an, die realtek geht auch
ceni funzt nur kde findet in seinen settings nix, liegt also wohl eher mein problem bei kde ^^
was hat kde damit zu tun? wenn netz geht mit ceni, dann geht es.
greetz
devil
naja man hätte halt schon gerne ein os "aus einem stück" und wenn ich bei KDE auf settings --> network gehe würd ich da schon gern mal meine netzwerke sehen und verwalten können .... denn dort ist alles leer als wäre kein gerät erkannt ;)
Hi Nemesis2k,
der network-manager vom KDE hat so seine Eigenheiten, deshalb wird hier ceni, wpa_supplicant, wpa_gui (WLAN-Roaming) empfohlen und supported. Außerdem kannst mit folgenden Kommandos sehen ob dein Netwerk funktioniert:
Listet alle vorhanden aber nicht unbedingt aktiven Netzwerkdevices auf
# ifconfig
eth0 Link encap:Ethernet Hardware Adresse 00:16:41:ab:7c:cf
inet Adresse:192.168.178.69 Bcast:192.168.178.255 Maske:255.255.255.0
inet6-Adresse: fe80::216:41ff:feab:7ccf/64 Gültigkeitsbereich:Verbindung
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:6216 errors:0 dropped:0 overruns:0 frame:0
TX packets:803 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:979476 (956.5 KiB) TX bytes:156059 (152.4 KiB)
Interrupt:16 Speicher:ee000000-ee020000
lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:16436 Metrik:1
RX packets:213 errors:0 dropped:0 overruns:0 frame:0
TX packets:213 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:0
RX bytes:15258 (14.9 KiB) TX bytes:15258 (14.9 KiB)
Zeigt dir ob du eine Verbindung ins Internet hast (Flag G - hier über das LAN-Device)
# netstat -nr
Kernel-IP-Routentabelle
Ziel Router Genmask Flags MSS Fenster irtt Iface
192.168.178.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
0.0.0.0 192.168.178.1 0.0.0.0 UG 0 0 0 eth0
Netzwerkdevice an und aus
# ifup eth0
# ifdown eth0